Re: Great new SiLentStepStick TMC2208 is not silent ;(
QuoteDust your inside a big wooden reverberation box... add some sound dampening foam. Wooden box is another problem. In this post I search for motors / stepper driver noise solution.
View ArticleRe: Great new SiLentStepStick TMC2208 is not silent ;(
If you have to stick with Mega2560 and Ramps, you can try to use a separate 24V or 36V powersupply for the stepper drivers only. That made a huge difference for my TMC2100, but it really got silent...
View ArticleRe: 6-lead steppers: lower current = more torque?:S
Finally tested the other wiring option ( 1.6mH ) and it made all the difference. I could run the M10 leadscrew at 600mm/min which is 4 times faster than before. ( although I turned the current down to...
View ArticleRe: Great new SiLentStepStick TMC2208 is not silent ;(
Quoteo_lampe If you have to stick with Mega2560 and Ramps, you can try to use a separate 24V or 36V powersupply for the stepper drivers only. That made a huge difference for my TMC2100, but it really...
View ArticleRe: Great new SiLentStepStick TMC2208 is not silent ;(
QuoteBut I can't understand difference with mega2560 and 32-bit controller with the same stepper driver and only 80steps per mm. The 8bit MPU is able to produce the step-pulses fast enough, but they...
View ArticleCan You Solve This Trouble?
Hello~(:P) Can I ask you some advice about DRV8801 which is full-bridge motor driver. As the datasheet of DRV8801 shows: it provides a versatile motor driver solution with a variety of...
View ArticleRe: Can You Solve This Trouble?
What kind of motor do you want to drive with this? If it's a brushed DC motor, how much Amps will it draw? ( It must be a very tiny motor , 'cause driver current is 2.8A peak )
View ArticleRe: Can You Solve This Trouble?
Hello~o_lampe It's a brushed DC motor with 2.5A. Regards
View ArticleRe: Can You Solve This Trouble?
You can start such a 2.5A motor without load only. The current demand at start is much higher than 2.8A. More like 28A :( Maybe the driver is in overcurrent protection or the PWM signal from...
View ArticleRe: Can You Solve This Trouble?
:( Anyway thanks for your suggestions !!! o_lampe you are kind !B) Best regards~
View ArticleNew Titan Slimline motor seizing
I realize that there is another post regarding a vibrating motor on the same page of this board, but that poster's solution had to do with his wiring and I am fairly certain that my wiring is fine as...
View ArticleRe: New Titan Slimline motor seizing
When you had it working by connecting it to the Y motor output, were you using the same cable as when you couldn't extrude with it? If you are not using the cable that came with it when trying to...
View ArticleRe: New Titan Slimline motor seizing
Yes, the same cable that I was not able to use on E0 was the same one that did work when connected to the Y motor output. It is the cable that came with it, and you're right, that cable is wired...
View ArticleRe: New Titan Slimline motor seizing
In general those 0.9° steppers like to run on higher voltages. The description on E3d page state it's a 2.7V motor, so it should run on 12V too. How did you try to extrude? Using the buttons of the...
View ArticleRe: Great new SiLentStepStick TMC2208 is not silent ;(
Quoteo_lampe QuoteBut I can't understand difference with mega2560 and 32-bit controller with the same stepper driver and only 80steps per mm. The 8bit MPU is able to produce the step-pulses fast...
View ArticleRe: Great new SiLentStepStick TMC2208 is not silent ;(
Hello all, Mr. Stephan replied to my question about TMC2208 noise: QuoteStephan Watterott The 12V power supply can also be a problem, because stepper motors are controlled with a constant current. So...
View ArticleMotors & Cable management (current rating)
Hello, I'm new here : I ordered a Prusa i3 clone with all the kit to assemble by hand, and i have to say i'm pretty satisfied of the prints I did until now :) . I want to organize the cables, because...
View ArticleRe: MKS LV8729 , a 128 µStep Driver // Any test?
Ordered from 3dpmav last Friday and today they are here. (tu) Four pieces 16 USD including shipping. Will try them soon.
View ArticleRe: MKS LV8729 , a 128 µStep Driver // Any test?
I think you'll be pleasantly surprised, as long as you don't want to move massive motors with heavy axes on them.
View ArticleRe: Motors & Cable management (current rating)
I don't think anyone has settled on a multifunctional connector for 3d printing yet. A connector with some low current and some high current options would make sense. The current per phase is for each...
View Article