Re: Programming using NanoPro from Nanotec
Hi, I am very new to operate this software can you just explain a little how to make sinusoidal profile for a stepper motor having step angle 0.014 degree..
View ArticleRe: Stepper Motors at Liquidation Prices!
Any other options for shipping besides UPS? I will NEVER ship UPS. (also being in Canada, the site will not accept my postal code)
View ArticleRe: Programming using NanoPro from Nanotec
... you can simply use a 1/128 microstepping driver - every impulse on the STP input will turn the motor a step ...
View ArticleRe: Stepper, torque, volts, pps
Hi Traumflug Don't really understand your reply Corner speed is the point of the torque curve where there is a sharp drop off in torque Have no headaches, trying make sense of it-as said in my first...
View ArticleRe: Applied Motion stepper configuration
I wired my applied motion steppers as Bipolar series. DJ
View ArticleRe: Stepper Motors at Liquidation Prices!
Can any one weigh in on if these are strong enough for a prusa i3? Also will they work with the ramps board just fine? If so I will buy some.
View Article3 Bad steppers, bad DIY breakout, or wrong settings in config.h?
First post, so if I do something stupid, don't send me down in flames. I bought some used steppers, built my own Gerbl breakout for a Uno, got some 4988 stepper drivers, set up GRBL as close as I can...
View ArticleRe: Stepper Motors at Liquidation Prices!
Mogal Wrote: ------------------------------------------------------- > Any other options for shipping besides UPS? > I will NEVER ship UPS. > (also being in Canada, the site will not accept...
View ArticleRe: Stepper Motors at Liquidation Prices!
SheldonE Wrote: ------------------------------------------------------- > You don't seem to ship to Australia. SheldonE, We can ship to Australia. I haven't had luck with automatically calculating...
View ArticleMoons 17HD Stepper Wiring Problem
I have a moons 17HD3802-02 stepper motor I am planning to use for my extruder. It is an eight-wire unit. See the following for specs. I am going to wire it as bipolar series, so I wired brown to white...
View ArticleRe: 3 Bad steppers, bad DIY breakout, or wrong settings in config.h?
Quoteall three will start off fine then act like they lock up or sit and "sing" and then maybe continue, maybe not. Does it sound right, like singing starting at a low tone, then raising, just to go...
View ArticleA3995 stepper driver for RAMPS
I found stepper driver 2.4A based on A3995. can I use this to replace POLOLU's A4988 for RAMPS?
View ArticleRe: Need a stepper driver recommendation
Why wouldn't you just use Pololu Stepper Driver Boards? These use A4988 stepper chips.
View ArticleRe: Need a stepper driver recommendation
Because 4988 will not do anywhere near 2.5 amps (Motors rated max), or 2 amps for that matter without serious heatsink and fans. You could get the 4988 black edition boards from Pololu that do a...
View ArticleStepper Motor Connector?
So I ordered some Nema 17 steppers for my Prusa Mendel, but the don't have wires coming out of it. they have a 6 pin straight connector. Does anybody know where I can find some of these connectors?...
View ArticleRe: Stepper Motor Connector?
There are thousands of variants of 6-pin connectors on this planet. With some luck you'll find the designation in the motors' data sheet; then you can search Mouser or DigiKey for that.
View ArticleRe: Need a stepper driver recommendation
Well said, but motors will run with less current than the specified maximum rating just fine. Essentially, the question is, what does the OP mean with "make them work". Work in which application? On a...
View ArticleRe: Stepper Motor Connector?
It might be one of the JST connectors, for example [www.digikey.com] Info found on [www.sparkfun.com]
View ArticleRe: Stepper Motors at Liquidation Prices!
hcker2000 Wrote: ------------------------------------------------------- > Can any one weigh in on if these are strong enough > for a prusa i3? They should be fine for the X, Y and Z axis, I...
View Article