I'm in the process of upgrading my Creality CR10 with Duet2Wifi. The Z axis stepper on the creality is slightly smaller 34mm.
I have been unable to get the the Z motor to respond at all. I've tried homing and sending G1 Z10 F1200 via pronterface. There's no vibrating or movement at all and the stepper turns freely as if it wasn't powered. When I replaced the stepper with a normal 40mm the stepper works and the Z commands work correctly.
I have tried swapping cables, upping the current in config.g, using the 2nd Z connection and bought a new 34mm stepper which also had the same problem.
Any idea what could be causing this?
Here are the specs on the stepper
------------------------------------------
1.5A 5oz.in (1HD00-22B)
Rated current: 1.5A
Holding torque: 5oz.in/20mN.m
Detent torque: 1.oz.in/12mN.m
Step angle: 1.°
Number of phase: 2
Insulation resistance: .2Ω
Rotor inertia: g.cm2
My current config.g
I have been unable to get the the Z motor to respond at all. I've tried homing and sending G1 Z10 F1200 via pronterface. There's no vibrating or movement at all and the stepper turns freely as if it wasn't powered. When I replaced the stepper with a normal 40mm the stepper works and the Z commands work correctly.
I have tried swapping cables, upping the current in config.g, using the 2nd Z connection and bought a new 34mm stepper which also had the same problem.
Any idea what could be causing this?
Here are the specs on the stepper
------------------------------------------
1.5A 5oz.in (1HD00-22B)
Rated current: 1.5A
Holding torque: 5oz.in/20mN.m
Detent torque: 1.oz.in/12mN.m
Step angle: 1.°
Number of phase: 2
Insulation resistance: .2Ω
Rotor inertia: g.cm2
My current config.g
G90 ; Send absolute coordinates... M83 ; ...but relative extruder moves ; Network M550 P"tronxy" ; Set machine name M552 S1 ; Enable network ;*** Access point is configured manually via M587 M586 P0 S1 ; Enable HTTP M586 P1 S0 ; Disable FTP M586 P2 S0 ; Disable Telnet ; Drives M569 P0 S0 ; Drive 0 goes backwards M569 P1 S0 ; Drive 1 goes backwards M569 P2 S1 ; Drive 2 goes forwards M569 P3 S0 ; Drive 3 goes backwards M350 X16 Y16 Z16 E16 I1 ; Configure microstepping without interpolation M92 X80 Y80 Z400 E99 ; Set steps per mm M566 X1200 Y1200 Z24 E300 ; Set maximum instantaneous speed changes (mm/min) M203 X30000 Y30000 Z600 E3000 ; Set maximum speeds (mm/min) M201 X1000 Y1000 Z1000 E5000 ; Set accelerations (mm/s^2) M906 X800 Y800 Z800 E800 I30 ; Set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z0 S0 ; Set axis minima M208 X300 Y300 Z400 S0 ; Set axis maxima ; Endstops M574 X1 Y1 Z1 S1 ; Set active high endstops ; Z-Probe M558 P0 H5 F120 T6000 ; Disable Z probe but set dive height, probe speed and travel speed ;M557 X40:280 Y40:280 S60 ; Define mesh grid M671 X50:50:250:250 Y60:260:260:60 S1.0 P0.5 ; Heaters M305 P0 T100000 B3988 R4700 ; Set thermistor + ADC parameters for heater 0 M143 H0 S120 ; Set temperature limit for heater 0 to 120C M305 P1 T100000 B3988 R4700 ; Set thermistor + ADC parameters for heater 1 M143 H1 S280 ; Set temperature limit for heater 1 to 280C ; Fans M106 P0 S0.3 I0 F500 H-1 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off M106 P1 S1 I0 F500 H1 T45 ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on M106 P2 S1 I0 F500 H1 T45 ; Set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on ; Tools M563 P0 D0 H1 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ; Custom settings are not configured ; Miscellaneous T0 ; Select first tool